Worbla’s Mesh(ed) Art (WMA) – Worbla with a one-sided mesh for strength!
Like all Worbla Products, Worbla’s Mesh Art is non-toxic and solvent-free. Worbla’s Mesh Art has also been partially made from recycled rice husks, as we are always looking to create more sustainable, environmentally conscious products.
Worbla’s Mesh Art is activated by heat (approx. 80-90° / 175-195°F), becomes mouldable and shapeable by hand when activated, and as all Worbla Products can be reheated endlessly until the desired shape is achieved.
Many of our tutorials on Worbla.com have suggested reinforcing areas for grommets and strapping/D-rings with Wonderflex, another thermoplastic you may be familiar with. Worbla’s Mesh art aims to provide the strength and tear-resistance that Wonderflex provides, while offering a cleaner, easier product with Worbla’s familiar sculpting properties.
- The mesh on Worbla’s Mesh Art does not form through the product when heated and shaped, even over complex curves. This means that the surface stays smooth – comparable to Worbla’s Finest Art.
- The adhesive in Worbla’s Mesh Art is stronger and tackier than Worbla’s Finest Art: this means it is even easier to blend seams and edges, but we do strongly suggest you work over a silicone sheet or parchment paper, as Worbla’s Mesh Art may stick very firmly to your workspace.
- Worbla’s Mesh Art can take complex curves, both positive and negative, just as well as Worbla’s Finest Art. Some edges may need slightly more blending, but you will not have the ‘dart’ or fold effect that Wonderflex can give.
- Worbla’s Mesh Art is stronger – a lot stronger – and resistant to tearing once heated and cooled. If you need a strong supported prop or accessory, you may be able to use one layer of Worbla’s Mesh Art when two layers of Finest Art would have been needed. You can also reinforce an area by layering Worbla’s Mesh Art behind Finest or Black Art.
- Worbla’s Mesh Art Scraps Can Be Recycled! Because there is a higher amount of adhesive plastic and a finer grid, scraps and bits of Worbla’s Mesh Art can be re-blended and used for sculpting with a surface only slightly more rough than reblended Finest Art scraps. It can also be mixed with Finest Art scraps, and even rolled into new sheets that will not be as strong as the original, but still have resilience. If you’ve ever tried to recycle Wonderflex scraps you know it’s difficult to get anything smooth.
- You will still need to prime Worbla’s Mesh Art, the same as Worbla’s Finest or Black Art, if you want a flat, shiny surface for painting.
- This last point is a bit more complicated, and we’re hoping to get a video done asap to show but in the meantime: Worbla’s Mesh Art is more flexible in that it can flex without breaking, compared to both Worbla’s Finest and Black Art. You can make ‘noodles’ out of Mesh Art, but note that it is not inclined to super organic curves on it’s own: If you are making noodles or similar for decoration to go ontop of another piece of Worbla, this isn’t an issue: You will be ‘gluing’ it into shape and so curves will be exactly as you want them. Freestanding curves – such as those for filigree bracelets or headpieces – can be tricker, as the mesh in the plastic means it will take a nice curve for 1-3 inches, and then want to take an angle, not a curve. We’d suggest using Finest Art or Black Art for very organic filigree work, and using Mesh Art for support ‘beams’ or pieces that curve less dramatically. Wonderflex noodles, in comparison, are almost impossible to curve and shape.
NOTE: While Techland takes steps to ensure accuracy in it's product listings and images, any color samples or lamp and product images shown on this website are for reference only, may not be exact and may vary from the actual product look and/or color.
Tell A Friend About: Mesh Art
Share this great product and savings with others. Note: You and your friend's email addresses are only used once for this recommendation. We do not collect nor store the email addresses.