DONE! Item Has Been Added To Your Cart

Your Cookies Are Disabled!

Our site uses first-party Cookies which must be enabled or you will not be able to use the shopping cart. These Cookies are not for ad tracking, are anonymous and have no personally identifiable data - they only hold cart data. [How To Enable]


TR-825 UHF Two-Channel Binaural Wireless Beltpack Single

(0 Review/s) Write a Review


LIST: $2,660.00SAVE $239.40 (9.0% OFF LIST PRICE)

TL Item#: 73665 MFR Part#: TR-825 Category: Comm Systems

On/Off & Volume Control
Turns the beltpack power on and controls head set volume.

Wireless Talk Around (WTA)
When pressed, the user’s audio is disconnected from the wired intercom, auxiliary input/output and the base station’s local headset. Other beltpack users, on that audio channel, can hear the user as normal.

Stage Announce (SA)
When pressed, the user’s audio is routed to the stage announce connector on the back of the base station. The user also loses their sidetone as an indication that stage announce is activated. The other wireless beltpacks and wired users do not hear the user’s audio. The button is non-latching and activates the nearby red LED.

Audio Channel Select Button
Allows user to select either audio channel A or B.

Bat/Overmod Light (BAT/OM)
Light will flash once when unit is turned on if the battery is good. If the light stays on, battery is low. If the light does not flash, battery is dead. A normal microphone gain setting will cause the LED to flash at the beginning of most words at normal speech levels. If the gain is too high, the LED will be red during the complete word at normal speech levels.

Talk Light
LED is on when the talk button, SA or WTA is active.

Talk Button
Press to enable the audio path from the local headset microphone. The “TALK” LED, #6, will turn red when enabled. A quick press and release latches the talk function, unless latching has been disabled. Holding the button for over ½ a second will cause the audio path to be enabled only for as long as the button is held. If the talk function is latched on, pressing the talk button again will turn it off.

  • Antenna: ¼ Wave (supplied), Screw type, Replaceable TX and RX
  • Binaural: Yes
  • Color: Black
  • Current Draw: 190 mA Push-to-Talk, A and B Talk On
  • Depth: 2.02" (51.3 mm)
  • Distortion: < 1 % at full deviation
  • FCC ID: B5DM517
  • Form Factor: Beltpack
  • Frequency Response: 300 Hz-8 kHz
  • Function: User Station
  • Height: 5.35" (135.9 mm)
  • IF Selectivity: 3 dB at 230 kHz
  • Image Rejection: 70 dB or better
  • Local Headset Output: 40 mW output into 600W 1% distortion
  • Microphone Input Sensitivity: 7 mV
  • Power Requirements: 6 “AA” Cells Alkaline NiMH optional
  • RF Frequency Range: 470 - 608 MHz, 614 - 740 MHz in 18 MHz TX and RX bands
  • RF Frequency Stability: 0.01 %
  • RF Sensitivity: < 0.7 μV for 12 dB SINAD
  • Squelch Quieting: 90 dB
  • Squelch Threshold: 20 dB SINAD About 1.0 μV
  • Storage Temperature: -4° F to 130° F (-20° C to 55 °C
  • Type: Dual Conversion Super heterodyne, Synthesized, FM, 712 channels
  • Weight: 1.31 lbs (0.6 kg)
  • Width: 3.75" (95.3 mm)
NOTE: While Techland takes steps to ensure accuracy in it's product listings and images, any color samples or lamp and product images shown on this website are for reference only, may not be exact and may vary from the actual product look and/or color.

Tell A Friend About: TR-825 UHF Two-Channel Binaural Wireless Beltpack

Share this great product and savings with others. Note: You and your friend's email addresses are only used once for this recommendation. We do not collect nor store the email addresses.

See all products by RTS

2420 Center St, Houston TX 77007 | United States | 832-518-5583